Skinner Pipeline Clamps

Harvey Pipeline Systems are the UK’s licensed supplier for Skinner Pipeline Clamps.  Below are the products we currently offer along with useful free PDF downloads.  You will need a suitable PDF reader to view the downloads such as Adobe Reader or have your browser set to read PDF files automatically.

skinner-pipeline-clamp

Skinner Pipeline Clamp

There is nothing like the Skinner-Seal Pipeline Clamp for long splits or extensive corrosion resulting in a series of pit holes. It has the same construction as the Emergency Pipe Clamp except it is double in length. The ample weight of this clamp gives a generous margin of safety for high pressure work.

With bolts along one side and a hinge along the other side, the Skinner Pipeline Clamp can be quickly installed under pressure without any interruption of service.

The Pipeline Clamp is manufactured from ductile iron, and equipped with a crescent-shaped pressure-equalizing gasket for every individual pipe size which is cemented into place.

The gasket is Buna-N and this clamp has 10 ft/lb of torque and 600 psi working pressure. It can withstand temperatures of up to 250 degrees Fahrenheit.

Specifications:
Length – 7 1/2″
Width – 2 1/8″
Bolt Diameter – 5/16″
Bolt Length – 2″
Number of Bolts – 4

For full details, please download the Skinner Pipeline Clamp PDF

emergency-clamp

Skinner Emergency Clamp

The Emergency Pipe Clamp is used for repairing pit holes, splits and corrosion leaks in both steel and cast iron pipe lines. The clamp is totally effective under extreme pressure or temperature. For over 100 years, the Emergency Pipe Clamp has been the universal repair clamp of choice, worldwide.

The clamp can be used on pipes for gas, water, oil, or ammonia. The repair lasts for years.

The Emergency Pipe Clamp offers triple savings including the cost of new pipe, the time and labour of replacing old pipe, and the expense of shutting down the system while the work is being done.

Installation of the Emergency Pipe Clamp is easy. Because of the long open hinge, the two halves of the clamp slide together along the pipe when conditions are crowded. The clamp is usually put on under pressure, without interruption of service. The gasket is cemented into a slight recess in the bottom half side so that the clamp can be installed easily under the most awkward conditions. The Emergency Pipe Clamp is manufactured from ductile iron, strongly proportioned, and fitted with sturdy, electroplated Grade 5 steel bolts. All clamps are E-coated to resist rust and the gaskets are Buna-N.

This clamp has 10 ft/lb torque and 600 psi working pressure. It can withstand temperatures up to 250 degrees fahrenheit.

Specifications:
Length – 3 1/4″
Width – 1 3/4″
Bolt Diameter – 5/16″
Bolt Length – 2″
Number of bolts – 2

For full details, please download the Skinner-Emergency-Pipe-Clamp PDF.

pressed-steel-wide-clamp

Skinner Pressed Steel Wide

The Pressed Steel Wide Clamp is used for repairing badly pitted and corroded pipe lines at minimum cost.

This is not a thin spring-steel band with attached lugs. It is a 3/16″ thick steel plate with inseparable “wedge-shaped” lugs pressed out of the material itself. This special construction prevents any give or collapse of the lug so that the full amount of take-up pressure applied by the bolts is transmitted directly to the gasket over the leak. While the clamp is heavy enough to outlast the pipe, it is still sufficiently flexible to conform to the pipe surface.

The Pressed Steel Wide Clamp is 8″ wide for running corrosion spots, complete with a crescent shaped, pressure equalizing gasket of Skinner Special Composition for use on oil or gas lines.

Large 5/8″ diameter steel bolts, plated and iridite-dipped are furnished with all clamps. This clamp has 60 ft/lb torque and 500 psi of working pressure. It can withstand temperatures up to 250 degrees Fahrenheit.

For full details, please download the Skinner-Pressed-Steel-Clamp PDF

pressed-steel-narrow-clamp

Skinner Pressed Steel Narrow

The Pressed Steel Narrow Clamp is used for repairing badly pitted and corroded pipe lines at a minimum cost.

This clamp is not a thin spring-steel band with attached lugs. It is a 3/16″ thick steel plate with inseparable “wedge-shaped” lugs pressed out of the material itself. This special construction prevents any give or collapse of the lug so that the full amount of take-up pressure applied by the bolts is transmitted directly to the gasket over the leak. While the clamp is heavy enough to outlast the pipe, it is still sufficiently flexible to conform to the pipe surface.

The Pressed Steel Narrow Clamp is 4″ wide for pit holes, complete with cone plug gasket fastened in place.

Large 5/8″ diameter steel bolts, plated and irridite-dipped are furnished with all clamps. This clamp has 60 ft/lb torque and 500 psi of working pressure. It can withstand temperatures up to 250 degrees Fahrenheit.

For full details, please download the Skinner-Pressed-Steel-Clamp PDF